The tutorial is as follows:

1) First prepare a pair of suitable slippers soles (commonly available in small commodity markets, very cheap), Then use cardboard to accurately copy the sole of the shoe, and cut 2 pieces according to the paper pattern. (One piece is for the visible face. Color matching needs to be considered. The fabric should be elastic. The other piece is the bottom. Scrap cloth can be used, but it should be thicker. of), In addition, you need to cut a piece of cotton (not too thick) or a thin sponge of the same size, and a hard cloth that is 1.5cm smaller or iron the base cloth with a cloth lining.

2) Stack the upper, cotton, hard lining, and bottom cloth in turn, and then fix it on the surrounding edge (0.5cm). While sewing, put some scraps of cotton in the middle, so that it feels better when you step on it, but you must follow The regularity of the feet is good, otherwise it would be better not to plug them, JMs will experience it by themselves.

 4) The shoe upper is going to be done below. I will use the software to draw the pattern of the shoe upper again at the end. (Note: A good way to be lazy on the upper is to cut off the old slippers, iron them flat, and copy them to paper, but pay attention to the stitched side to release 1CM), just look at the process of taking pictures, and have shoes After the surface pattern, you need to cut a piece of face (consider color matching), a piece of lining (slightly thin, soft, preferably knitted fabric), and a piece of fine cotton (or a thin sponge), plus a layer of hard lining (hard spots can be used) Replace the cloth such as canvas) 7 (this layer needs to be 1.5cm smaller than the paper pattern). This way the upper will be more stylish and will not collapse.

5. Align the upper, cotton, hard lining and lining cloth in sequence, and fix a circle around it (preferably 0.5CM stitched), The trick in this step is to make sure that the lining should be overlaid and the face should be oversewn, otherwise the lining will be uneven. Pay attention to the reverse side:

6) Wrinkle a section of the round toe of the shoe so that the toe toe is arched in an obvious arc, but it is better not to have obvious folds. This requires the sisters to carefully understand this, and at the same time piping the shoe mouth, ( The material of the piping should also consider the overall color matching)

7) This step is to sew the finished upper to the finished sole The key points are: make 3 alignment stitching points, first, the center point of the toe is to the center point of the sole; second, the left end of the upper is aligned with the left starting point of the sole, and third, the right end of the upper is aligned The right end of the sole. Then sew them one by one, and when sewing to the round-head wrinkles of the upper, pay special attention to shrink the round-head upper to the sole, but there should be no obvious wrinkles.

8) piping the sole and upper together, and stitch the first stitch on the front of the shoe; The second stitching is best to sew by hand, and the piping can be tightened and fixed on the back of the sole. Pay attention to the reverse side

9) a Fix the rolled shoes to the ready-made foam soles, first put the cloth bottom of the slippers on the foam soles and evenly select 3 to 4 points for stitching in position, and fix these points first Stitched together
b Then sew one week in turn; the stitching method uses back stitches, but the stitch length can be larger, which is faster;
c The stitching position is on the seam of the piping or directly on the piping, but the stitches are even to look good. The thread should be unobtrusive, thick polyester thread or nylon thread.
d This step requires a lot of effort. You need to bring all the tools. The needle is larger, but it is not the largest one in the box. The middle finger needs to wear a hard thimble, and the index finger needs to wear a plastic finger cot, so that stitching is easy. too much
e There are also gun powder soles, it is best to buy softer ones, preferably with grooves at the bottom, so that the stitches are directly sewn into the grooves, which is easier to grasp. If there is no groove, then ask for the sole. People will teach you how to deal with it